alarm-instalacja.pdf

(740 KB) Pobierz
Original BMW Accessories.
Installation Instructions.
Alarm Retrofit Kit
BMW 3 Series Sedan (E 46/4)
BMW 3 Series Coupe (E 46/2)
Vehicle must have alarm pre-wiring, which is 100% option for US spec vehicles.
Retrofit kit No.
65 73 9 416 520
Alarm Retrofit Kit
Installation time
The installation time is 1,0 hours, but this may vary depending on the condition of the car and the
equipment in it.
Suggested installation time includes re-coding of the vehicle only for this retrofit kit. This time is based
on a vehicle that is at the current software level and does not require any updates. Before installing this
accessory into the vehicle, the vehicle should be connected to the DIS and checked for software
updates. If updates are available the vehicle should be programmed prior to installing this accessory.
Please refer to SI B09 05 01 for latest BMW approved CIP Retrofit procedures.
Important information
To avoid unnecessary extra work and/or costs, if any installation or function problems occur,
after a brief troubleshooting session (approx. 0.5 hours), contact the following:
1. Either your national sales company or your regional office or
2. The Support team via the Aftersales Assistance Portal (ASAP) using the optional technical
parts support application.
Quote the VIN and the part number of the retrofit kit and provide a detailed description of the
problem.
The instructions below are developed for BMW vehicles and are not to be compared to any other
existing instructions for vehicles other than BMW. No methods other than those specified in this
document are to be used for installation in BMW vehicles. Left and right are determined from the driver’s
seat.
Carefully read all instructions and supplements before proceeding with the installation. Reference
should be made to TIS for instructions dealing with a stock part of the vehicle but not stated in detail in
these instructions.
The instructions were complete and up to date at time of publication; however, changes to the vehicle
or installation may have occurred. Please report any problems or changes noted with the installation to
BMW Technical Hotline, along with VIN, date of manufacture and as much detail as possible.
Do not archive the hard copy of these installation instructions since daily updates are made by ASAP.
© BMW AG, München
01 21 9 416 538
03.2006
1
PARTS INFORMATION
Contents of Kit – P/N 65 73 9 416 520
Description
M6 Hex nut w/captive flat washer
M6 x 16 mm Hex bolt w/captive flat washer
M6 Prestol-cage clip
5 Amp fuse
Siren bracket
Tilt sensor
Siren (USA)
Ultrasonic module
Qty
3
1
1
1
1
1
1
1
BMW Part Number
11 61 1 708 413
07 11 9 915 039
32 41 1 095 443
61 13 1 386 626
65 75 8 377 290
65 75 6 923 215
65 75 8 383 153
65 75 6 938 048
© BMW AG, München
01 21 9 416 538
03.2006
2
Contents
Section
1.
2.
3.
4.
Page
4
6
7
8
Siren Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inclination Sensor Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior Module Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Retrofit coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
© BMW AG, München
01 21 9 416 538
03.2006
3
1.
Siren Mounting
1
Disconnect negative battery terminal.
2.
Release (¼ turn) the three spring loaded
fasteners (1) on grill cover (2).
3.
Remove air collector (3).
1
2
3
5$# '& 7"!
3
2
4.
Carefully pry up on the four upper retainers (1)
and remove cable channel cover (2) from the
cable channel.
5.
Remove the wire harnesses from the harness
channel
6.
Loosen the four 30 Torx head captive bolts (3)
and remove forward cowl panel.
1
5$# '& 7""
1
2
7.
Loosen the two 30 Torx head captive bolts (1) on
rearward cowl panel (3).
8.
Release (¼ turn) plastic retainer (2) and remove
from rearward cowl panel. It may be necessary to
carefully pull forward/push rearward on the
rearward cowl panel (3) to aid in the removal of
this plastic retainer.
3
5$# '& 7"#
1
9.
Look into the RH (passenger's side) area of
firewall area (1) to determine mounting fastener
requirements. If M6 threaded insert or M6 cage
clip is already in place, proceed to step 11. If a
square hole is in this location, proceed to step 10.
5$# '& 7#
© BMW AG, München
01 21 9 416 538
03.2006
4
1. Siren Mounting
10.
Insert cage clip nut (2) into square hole (1). Press
firmly on cage clip until it is fully flush with
mounting surface.
1
2
5$# 7%#
2
3
1
11.
Assemble alarm siren (2) to mounting bracket (1)
using M6 nut with captive flat washer (3).
5$# '& 7"$
1
2
4
12. Locate and terminate 4-position alarm
siren connector (2) to alarm siren (1).
13. Position alarm siren/mounting bracket
assembly into mounting position utilizing the
positioning tab (3) and secure alarm siren
assembly in place with M6x16mm bolt with
captive flat washer (4).
3
5$# '& 7"%
14. Re-assemble all displaced or previously
removed parts.
© BMW AG, München
01 21 9 416 538
03.2006
5

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin