NewOrleansSquare.pdf

(7994 KB) Pobierz
Ray Keim, at Haunted Dimensions, has created this project solely for the purposes of entertainment.
It is not to be repackaged or resold.
KEEP IT FREE!
When completed, the model is approximately 9.25 inches (23 cm) high, 9.25 inches (23 cm) wide and 10 inches (26 cm) deep.
Much time and effort has gone into the creation of this model of the New Orleans Square Haunted Mansion. The architectural, and
artistic details are extremely accurate, however some artistic license was taken, in order to translate the mansion to paper.
Please note that this project is not recommended for children. It requires a moderate degree of skill, and the use of an X-acto blade,
which is extremely dangerous. I HIGHLY recommend wearing protective eyewear when using an X-acto blade! Tips can snap and fly!
When printing the model, be sure that your printer is set to print at 100%. Each sheet has a logo, and page number graphic, which can
be compared with other sheets, to ensure that all of your pieces are printed at a uniform size. Color printing is recommended.
There are many pages to print, so be sure you have enough paper and ink! This model was designed to be printed on EPSON Matte
Paper Heavyweight. Using plain paper is not recommended.
The files are in .pdf format, so you will need a computer with Adobe Acrobat Reader installed.
I recommend using white glue, and applying it with a toothpick. Don’t use too much glue! Needle-nose tweezers are also very useful.
Become acquainted with the various pieces, and
study the directions before you begin.
The text instructions that accompany the
illustrations are limited, so you will need a keen eye and a good sense of spatial orientation to assemble
the New Orleans Square Haunted Mansion.
There are many folds in the model, and it is recommended that you score the fold first, using a dull X-acto, or other fine, blunt tipped
instrument. Black dashed lines represent a mountain fold (a fold which point upward), and orange dashed lines represent a valley fold
(the fold points downward). The orange dashed lines are accompanied by a red “
+
” at each end. These are to be used as pin guides to
,
poke small holes at the “
+
” flip the sheet over, and score between the holes for a clean valley fold.
To avoid confusion, after cutting out a part, lightly write the part numbers on the back with a pencil.
I created this model for my own enjoyment, but choose to share it with others. By downloading this model, you agree that the success
of the final product is primarily determined by the patience and skill of the builder.
Have fun building your New Orleans Square Haunted Mansion, and good luck!
Welcome, foolish mortal, to The New Orleans Square Haunted Mansion Paper Model Kit!
There’s no turning back now!
http://www.haunteddimensions.raykeim.com/
Fold indicators:
To make a valley fold
=
=
mountain fold
(
points to you
)
valley fold
(
points away from you
)
Cutting out the windows
is optional.
If you choose to remove the windows,
score and assemble the 32 window inserts
and 2 door insets found on page 8
Score and assemble the mansion walls. Be sure to cut all slots wide enough
to allow easy tab insertions
(a
single cut may not be wide enough).
Glue the window insert behind the corresponding window openings.
Score, fold and insert the base, 6A bottom
6A
bottom
Score and fold corner pieces 5A and 5B and glue into place on building core.
Page 1
You may want to wait to do this step on page 4
if you believe it will make tab insertions easier.
Score, fold and insert
top support "7A top".
Be sure the base tabs 9B and 10B are flush with bottom edges and do not protrude.
Score, fold and assemble porch pieces 9A and 10A
and insert the support bases 9B and 10B.
9A
10A
10B
9B
Glue porch 9A into place as shown,
then glue porch 10A into place.
Score and fold the first floor ironwork pieces
11A, 11B, and 11C and glue into place using tabs.
Apply a small amount of glue to the back of each tab before inserting.
For a more realistic effect, print the ironwork pages on color inkjet transparancy sheets,
found in most office supply stores
Page 2
Apply a few small drops of glue
along the top edges of the ironwork 11A, 11B and 11C.
Score, fold and insert second floor piece 12A inserting
the porch tab into slot under the second floor door base.
Also slip the center porch slot over the ironwork 11A tab.
Set porch piece 12B into place, inserting porch tab
into slot under the second floor door base. Also glue
the left edge on to the overlap of piece 12A.
Apply a small amount of glue to the back of each tab before inserting.
Score and fold the second floor ironwork pieces
13A and 14A. Fold down the long top tabs,
then glue pieces into place using bottom tabs.
Score and fold and construct
the verandah roof pieces
115A,15B, 15C, 15D.
Glue 15B to the tab of 15A.
Glue 15C to tabs of 15D.
Page 3
Optional time to insert
top support "7A top".
If you chose not to do it on page 2
Apply a few small drops of glue along the top edges of
the second floor ironwork 13A and 14A
and along the corner edges of 5A and 5B.
First attach the 15AB section, inserting the roof
tabs into the two wall slots.
Then attach the 15CD section using the two tabs, and also
glue to the corner flaps of the 15AB section.
At this point use tiny drops of glue to nail down any loose
areas of the porch roof and ironwork.
Score and prefold the portico pieces 16A and 16C.
Optional: Cut around the heavy black line within the center triangles, if you would like to make the pediments
more dimensional by adding the pediment inserts.
Carefully glue the inserts behind each triangular opening.
Page 4

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin