CCNA Configuration SIM Question.pdf

(70 KB) Pobierz
1|
Page
CCNA Configuration SIM Question
Question:
To configure the router (R2-RC) click on the console host icon that is connected to a router by a serial
console cable (shown in the diagram as a dashed black line)
CCNA Training Company recently installed a new router in their office. Complete the network
installation by performing the initial router configurations and configuring RIPV2 routing using the
router command line interface (CLI) on the R2-RC.
Name of the router is
R2-RC
Enable-secret password is
cisco1
The password to access user EXEC mode using the console is
cisco2
The password to allow telnet access to the router is
cisco3
IPV4 addresses must be configured as follows:
Ethernet network
209.165.202.128/27
– router has last assignable host address in subnet
Serial network is
192.0.2.16/28
– router has last assignable host address in the subnet. Interfaces
should be enabled.
Router protocol is
RIP V2
Attention :
In practical examinations, please note the following, the actual information will prevail.
1. Name of the router is xxx
2. Enable-secret password is xxx
3. Password to access user EXEC mode using the console is xxx
4. The password to allow telnet access to the router is xxx
5. IP information
Solution
2|
Page
1) Name the router:
Router>enable
Router#configure
terminal
Router(config)#hostname
R2-RC
2) Set secret password:
R2-RC(config)#
enable secret cisco1
3) Set password for the console:
R2-RC(config)#line
console 0
R2-RC(config-line)#password
cisco2
R2-RC(config-line)#login
R2-RC(config-line)#exit
4) Set the Telnet password:
R2-RC(config)#line
vty 0 4
R2-RC(config-line)#password
cisco3
R2-RC(config-line)#login
R2-RC(config-line)#exit
5) Assign IP address for Ethernet interface (Fa0/0):
The Ethernet network
209.165.202.128/27
has:
Increment:32
(/27 = 255.255.255.224 or 1111 1111.1111 1111.1111 1111.1110 0000)
Network address:
209.165.202.128
Broadcast address:
209.165.202.159 (because 128 + 32 – 1 = 159)
Therefore the last assignable host address in this subnet is
209.165.202.158
and we will assign it to
Fa0/0 interface with these commands:
R2-RC(config)#
interface fa0/0
R2-RC(config-if)#ip
address 209.165.202.158 255.255.255.224
R2-RC(config-if)#no
shutdown
R2-RC(config-if)#exit
6) Assign IP address for Serial interface (S0/0/0):
Serial network
192.0.2.16/28
has:
Increment:16
(/28 = 255.255.255.240 or 1111 1111.1111 1111.1111 1111.1111 0000)
Network address: 192.0.2.16
Broadcast address:
192.0.2.31 (because 16 + 16 – 1 = 31)
So the last assignable host address in this subnet is
192.0.2.30.
Finally we assign it to s0/0/0
interface:
R2-RC(config)#
interface s0/0/0
R2-RC(config-if)#ip
address 192.0.2.30 255.255.255.240
R2-RC(config-if)#no
shutdown
R2-RC(config-if)#exit
7) Configure RIP v2 routing protocol:
3|
Page
R2-RC(config)#router
rip
R2-RC(config-router)#version
2
R2-RC(config-router)#network
209.165.202.128
R2-RC(config-router)#network
192.0.2.16
R2-RC(config-router)#end
R2-RC#copy
running-config startup-config

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin