1201.PDF
(
29 KB
)
Pobierz
MAX840 Evaluation Kit
_______________General Description
The MAX840/MAX843/MAX844 ICs are inverting,
charge-pump DC-DC converters with low-noise, regu-
lated outputs. Their low output ripple voltage makes
these devices ideal for biasing the GaAsFETs com-
monly found in cellular telephone transmitters.
The MAX840 evaluation kit (EV kit) is a fully assembled
and tested surface-mount board. The board is shipped
with a MAX840 mounted, but it can be replaced by the
MAX843 or MAX844. Provisions are made for mounting
two additional resistors, which are required for output
voltages other than -2V. A special scope-probe socket
is also mounted on the board, so output noise can be
observed on an oscilloscope.
____________________Component List
DESIGNATION QTY
C1, C2, C3
3
DESCRIPTION
0.22µF ceramic capacitors
Vitramon VJ1206Y224KXX
Murata GRM42-6X7R224M025
4.7µF, 16V low-ESR tantalum
capacitor, Sprague 595D475X0016A
Matsuo 267E 2002 475
Open
3-pin header
Scope probe connector,
Specialty Connectors 33JR135-1
Maxim MAX840ISA 8-pin SO
Shunt
Printed circuit board
Evaluates: MAX840/MAX843/MAX844
C4
R1, R2
J1
J3
U1
None
None
1
0
1
1
1
1
1
___________________________Features
o
1mVp-p Output Voltage Ripple
o
2.5V to 10V Input Range
o
Uses 0.22µF Capacitors
o
-2V Regulated Output (or Adjustable)
o
4mA Output Current
o
Surface-Mount Technology
______________Component Suppliers
SUPPLIER
Matsuo
Murata-Erie
Sprague
Vishay/Vitramon
Specialty Connectors
PHONE
(714) 969-2491
(814) 237-1431
(603) 224-1961
(203) 268-6261
(317) 738-2800
FAX
(714) 960-6492
(814) 238-0490
(603) 224-1430
(203) 452-5670
(317) 738-2858
V
IN
1
J1
2
3
GND
C1
0.22µF
C3
0.22µF
3
SHDN
4
1
2
8
7
6
5
R1
OPEN
C4
4.7µF
V
OUT
-2V
C2
0.22µF
J3
NEGOUT
SHDN
OUT
FB
V
OUT
C1+
C1-
U1
MAX840
IN
GND
V
IN
2.5V TO 10V
GND
R2
OPEN
J2
CUT HERE
V
CTRL
GND
Figure 1. MAX840 EV Kit Schematic Diagram
_______________________________________________________________________________________
1
MAX840 Evaluation Kit
Evaluates: MAX840/MAX843/MAX844
_________________________Quick Start
The MAX840 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Do
not turn on the power supply until all connections
are completed.
1) Connect a 2.5V to 10.0V supply to the VIN pad at
the top of the board. Connect the ground lead to
the adjacent GND pad.
2) Connect a voltmeter and the load to the VOUT pad.
3) Place the shunt on J1 across pins 1 and 2. This
— —
— –
connects the SHDN pin to V
IN
.
4) Turn on the power and verify that the output is -2V.
You can insert a scope probe into J3 to observe the
output noise. Be sure the scope ground makes con-
tact with the outside of the connector.
— —
— –
The 3-pin header, J1, controls pin 4 (SHDN
)
on the IC.
Table 1 outlines the shunt positions for J1.
install two resistors (R1 and R2) for the output voltage
divider. Mounting pads for the resistors are located on
the board’s solder side. See the MAX840/MAX843/
MAX844 data sheet for instructions on calculating R1
and R2 values.
If using the MAX843 or MAX844 with the MAX840 EV kit,
connect V
CTRL
to a positive voltage to control V
OUT
.
V
OUT
= -V
CTRL
(R2 / R1)
For example, if R1 = R2, then V
OUT
= -V
CTRL
. The max-
imum
|
V
OUT
|
will be at least 0.6V below V
IN
.
Table 1. J1 Shunt Positions
SHUNT POSITION
1&2
2&3
PIN 4
CONNECTION
V
IN
GND
Connected to
pad
MAX840
FUNCTION
— —
— –
SHDN high,
device enabled
— —
— –
SHDN low,
device disabled
Pin 4 is driven by
user signal
connected to
— —
— –
SHDN pad
_______________Detailed Description
Output Voltage Adjustment
For output voltages other than -2V, cut the trace across
J2 to disconnect the FB pin (pin 5) from GND, and
Open
Figure 2. MAX840 EV Kit Component Placement Guide—
Component Side (not shown to scale)
Figure 3. MAX840 EV Kit Component Placement Guide—
Solder Side (not shown to scale)
Figure 4. MAX840 EV Kit PC Board Layout—Component Side
(not shown to scale)
Figure 5. MAX840 EV Kit PC Board Layout—Solder Side
(not shown to scale)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
2
___________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1996 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Plik z chomika:
Kot_Maciek
Inne pliki z tego folderu:
0001.PDF
(10 KB)
1003.PDF
(374 KB)
1002.PDF
(139 KB)
1004.PDF
(342 KB)
1005.PDF
(170 KB)
Inne foldery tego chomika:
PDF2
PDF3
SPICE
Zgłoś jeśli
naruszono regulamin