1147.PDF

(37 KB) Pobierz
19-0419; Rev 1; 9/95
MAX688-4A Evaluation Kit
_______________General Description
The MAX688-4A evaluation kit (EV kit) provides a regu-
lated 3.3V output voltage while operating on input volt-
ages from 3.5V to 11V. It delivers up to 4A output cur-
rent from a 4.5V to 5.5V input, with low dropout.
The MAX688-4A EV kit is a fully assembled and tested
printed circuit board. The board comes with a 3.3V-out-
put MAX688 IC installed, but can also be used to evalu-
ate the MAX689 (3.0V output).
____________________________Features
o
3.5V to 11V Input Supply Range
o
3.3V Output Voltage
o
Up to 4A Output Current
o
<0.02µA/MAX688 Shutdown Supply Current
o
150µA Quiescent Current
o
External PNP Pass Transistor
o
Adjustable Current Limit
o
Fully Assembled and Tested
Evaluates: MAX688/MAX689
____________________Component List
DESIGNATION QTY
C3
C4
1
1
DESCRIPTION
1µF ceramic capacitor
Marcon THCR30E1E105M
4.7µF, 16V tantalum capacitor
Sprague 595D475X0016A2B
150µF, 35V aluminum electrolytic caps.
Nichicon UPL1V151MPH6 or
Sanyo 35MV150GX
0.01µF ceramic capacitor
1200µF, 16V aluminum electrolytic cap.
Nichicon UPL1C122MRH6 or
Sanyo 16MV1200GX OR
1000µF, 25V aluminum electrolytic cap.
Sanyo 25MV100GX
10Ω, 5% resistor
100kΩ, 5% resistor
1kΩ, 5% resistor
PNP power transistor (TO-220)
Motorola TIP42A
PNP transistor, Motorola 2N4403
Heatsink, Thermalloy 6072B
Maxim MAX688CSA (8-pin SO)
3-pin header
2-pin header
Shunt
PC board
MAX688 data sheet
______________Ordering Information
PART
MAX688EVKIT-4A
TEMP. RANGE
0°C to +70°C
______________Component Suppliers
SUPPLIER
AVX
IRC
Marcon
Sanyo
Sprague
PHONE
(803) 946-0238
(213) 772-2000
(708) 913-9980
(619) 661-6835
(508) 339-8900
FAX
(803) 626-3123
(213) 772-9028
(708) 913-1150
(619) 661-1055
(508) 339-5063
C1, C2
C16
2
1
C5
1
_________________________Quick Start
The MAX688-4A EV kit is a fully assembled and tested
board. Follow these steps to verify board operation.
Do
not turn on the power supply until all connections
are completed.
1) Connect a 5V power supply to the pad marked
VIN. The ground connects to the GND pad.
2) Connect a voltmeter and load (if any) to the VOUT
pad.
3) Place one shunt across JU1 pins 2 and 3 and the
other shunt across JU2 for normal operation.
4) Turn on the power and verify that the output
voltage is 3.3V.
Instructions for modifying the board for a 3.0V output
appear in the section
Evaluating the MAX689.
R4
R1
R3
Q1
Q2
None
U1
JU1
JU2
None
None
None
1
1
1
1
1
1
1
1
1
2
1
1
________________________________________________________________
Maxim Integrated Products
1
Call toll free 1-800-998-8800 for free samples or literature.
MAX688-4A Evaluation Kit
Evaluates: MAX688/MAX689
_______________Detailed Description
Shutdown Function
The MAX688 has an active-low shutdown control input
to turn its output on or off at any time. The 3-pin header
JU1 selects the shutdown mode. Remove the shunt
when driving shutdown with an external signal. Table 1
lists the jumper selectable options.
Evaluating the MAX689
The MAX688 can be replaced with a MAX689 to gener-
ate a 3.0V output voltage with output current up to 4A.
The only modification required is to replace the IC.
Base-Current Limiting
The output current can be limited by installing a current-
limiting resistor, R2, between BASE (pin 7) and BLIM (pin
6) of U1. This EV kit comes with a shunt across JU2,
which limits base current to 20mA.
For lower base current limit, refer to the MAX687/
MAX688/MAX689 data sheet for instructions on selecting
the current-limiting resistor value.
Table 1. Jumper JU1 Functions
SHUNT
LOCATION
2&3
2&1
SHDN PIN
Connected to VIN
Connected to GND
MAX688 OUTPUT
MAX6884A Enabled,
V
OUT
= 3.3V
Shutdown Mode,
V
OUT
= 0V
R3
1k, 5%
VIN
C4
4.7µF
16V
3
2
1
JU1
SHDN
PFO
3
PFO
BLIM
6
C3
1µF
C1
150µF
C2
150µF
1
IN
Q1
TIP-42
Q2
2N4403
R4
10Ω, 5%
U1
CC
MAX688
8
C16
0.01µF
2
SHDN BASE
7
JU2
R2
OPEN, 5%
4
GND
OUT
5
C5
1000µF
25V
C6*
220µF
6.3V
C7*
1µF
x 10
VOUT
R1
100k
* NOTE: RECOMMENDED FOR FAST 0.2A TO 4A TRANSIENT LOAD
OPTIONAL *
Figure 1. MAX688-4A EV Kit Schematic Diagram
2
_______________________________________________________________________________________
MAX688-4A Evaluation Kit
Evaluates: MAX688/MAX689
Figure 2. Component Placement Guide—Component Side
Figure 3. PC Board Layout—Component Side
Figure 4. PC Board Layout—Solder Side
_______________________________________________________________________________________
3
MAX688-4A Evaluation Kit
Evaluates: MAX688/MAX689
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
4
___________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1995 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Zgłoś jeśli naruszono regulamin