GENERAL.pdf

(2098 KB) Pobierz
00-1
GROUP 00
GENERAL
CONTENTS
HOW TO USE THIS MANUAL. . . . . .
HOW TO USE
TROUBLESHOOTING/INSPECTION
SERVICE POINTS . . . . . . . . . . . . . . .
VEHICLE IDENTIFICATION . . . . . . .
GENERAL DATA AND
SPECIFICATIONS . . . . . . . . . . . . . . .
PRECAUTIONS BEFORE SERVICE.
00-2
SUPPLEMENTAL RESTRAINT
SYSTEM (SRS) . . . . . . . . . . . . . . . . . .
SRS SERVICE PRECAUTIONS . . . . .
00-6
00-16
00-20
00-22
SUPPORT LOCATIONS FOR LIFTING
AND JACKING . . . . . . . . . . . . . . . . . .
00-31
STANDARD PART/TIGHTENING-
TORQUE TABLE . . . . . . . . . . . . . . . .
00-33
00-27
00-28
00-2
GENERAL
HOW TO USE THIS MANUAL
HOW TO USE THIS MANUAL
SCOPE OF MAINTENANCE, REPAIR AND
SERVICING EXPLANATIONS
This manual provides explanations, etc. concerning
procedures for the inspection, maintenance, repair
and servicing of the subject model. Note, however,
that for engine and transmission-related component
parts, this manual covers only on-vehicle
inspections, adjustments, and the removal and
installation procedures for major components. For
detailed information concerning the inspection,
checking, adjustment, disassembly and reassembly
of the engine, transmission and major components
after they have been removed from the vehicle,
please refer to separate manuals covering the
engine and the transmission.
ON-VEHICLE SERVICE
"On-vehicle Service" is procedures for performing
inspections and adjustments of particularly important
locations with regard to the construction and for
maintenance and servicing, but other inspection (for
looseness, play, cracking, damage, etc.) must also
be performed.
INSPECTION
Under this title are presented inspection and
checking procedures to be performed by using
special tools and measuring instruments and by
feeling, but, for actual maintenance and servicing
procedures, visual inspections should always be
performed as well.
M1001000100660
REFERENCE VALUE
Indicates the adjustment value prior to starting the
work (presented in order to facilitate assembly and
adjustment procedures, and so they can be
completed in a shorter time).
DANGER, WARNING, AND CAUTION
DANGER, WARNING, and CAUTION call special
attention to a necessary action or to an action that
must be avoided. The differences among DANGER,
WARNING, and CAUTION are as follows:
•
If a DANGER is not followed, the result is severe
bodily harm or even death.
•
If a WARNING is not followed, the result could be
bodily injury.
•
If a CAUTION is not followed, the result could be
damage to the vehicle, vehicle components or
service equipment.
INDICATION OF TIGHTENING TORQUE
Tightening torques (units: N⋅m) are set to take into
account the central value and the allowable
tolerance. The central value is the target value, and
the allowable tolerance provides the checking range
for tightening torques. If bolts and nuts are not
provided with tightening torques, refer to
P.00-33.
MODEL INDICATIONS
The following abbreviations are used in this manual
for identification of model types.
MPI::Indicates the multipoint injection.
SOHC::Indicates an engine with the single overhead
camshaft.
DOHC::Indicates an engine with the double
overhead camshaft.
2000:: Indicates models equipped with the 2,000 mL
<4G63> petrol engine.
2400::Indicates models equipped with the 2,400 mL
<4G69> petrol engine.
M/T:: Indicates the manual transmission.
A/T:: Indicates the automatic transmission.
A/C:: Indicates the air conditioner.
DEFINITION OF TERMS
STANDARD VALUE
Indicates the value used as the standard for judging
the quality of a part or assembly on inspection or the
value to which the part or assembly is corrected and
adjusted. It is given by tolerance.
LIMIT
Shows the standard for judging the quality of a part
or assembly on inspection and means the maximum
or minimum value within which the part or assembly
must be kept functionally or in strength. It is a value
established outside the range of standard value.
GENERAL
HOW TO USE THIS MANUAL
00-3
NOTES
00-4
GENERAL
HOW TO USE THIS MANUAL
(s
.
<<A>>
>>A<<
disassembly.
or reassembly.
Symbols are used to show the locations for lubrication
.
These symbols are included in the diagram of compo-
nent parts or on the page following the component
parts page. The symbols do not always have accomp-
anying text to support that symbol.
Multi-purpose grease unless there is a
AC301960
GENERAL
HOW TO USE THIS MANUAL
00-5
For bolts and nuts which do
not have a tightening torque
listed, refer to the "Standard
Parts tightening-torque Table"
parts sets are
On removal,
reassembly are described
AC300860

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin